Duct Sealing
Leaking seams, loose joints and gaps at register boots let heated and cooled air escape before it reaches your rooms. We find the leaks on accessible ductwork, fasten loose connections and seal them with mastic sealant and foil tape.
- Certified & insured technicians
- Upfront pricing, no add-ons
- Service 7 days a week
- Homes & businesses
Duct Sealing That Keeps Air Inside the Ductwork
Duct sealing closes the gaps where ducts lose air: the seams along each section, the joints between sections and the connections at registers and the air handler. According to ENERGY STAR, a typical forced-air system loses 20 to 30 percent of the air it moves through leaks, holes and poorly connected ducts.
Leaks on the return side also work in reverse, pulling dusty attic, basement or crawl space air into the system and spreading it through the house or building. That is why sealing matters as much for dust as it does for comfort, and why ducts that run through unconditioned spaces are the first ones we check.
Sealing is manual work on the ductwork we can reach. Our certified, licensed and insured technicians inspect first, give you an upfront price for the joints that need work, then clean each joint, fasten it mechanically where it is loose and seal it with mastic or foil tape rated for duct use.
Need Leaking Ducts Sealed Soon?
Rooms that never reach temperature or dust that keeps coming back? Call (855) 501-0191 and we book a duct sealing inspection, 7 days a week, with an upfront price for the joints that need work.
Duct Sealing Services
Seams Along Duct Sections
Sheet metal duct sections are formed with seams along their length, and those seams open slightly over years of heating and cooling cycles. We clean the seam, then brush mastic over it so it sets into a flexible, airtight layer, or cover a clean flat seam with foil tape. Seams on ducts that run through attics and crawl spaces are sealed first, because air lost there leaves the conditioned space entirely.
- Seams cleaned before sealing
- Mastic or foil tape per seam
- Unconditioned spaces first
Joints and Fittings
Joints between straight sections, elbows and transitions are where most leaks start, especially where cloth tape was used in the original installation and has since dried out. We remove the failed tape and dust, check that the joint is tight, refasten it with sheet metal screws or a draw band if it is loose, and seal it.
- Failed tape removed
- Loose joints refastened
- Sealed over a clean surface
Register Boots
The register boot is the fitting that joins a duct to the floor, wall or ceiling, and the gap between the boot and the building opening is one of the most common leak points. We seal the boot to the duct and to the opening, so the register delivers its air into the room instead of into the wall or ceiling cavity.
Takeoffs and Collars
Takeoffs and collars are where branch ducts leave the main trunk. Flex duct pulled off a collar, or a takeoff never sealed, can dump a room’s air into an attic or basement. We reattach and fasten loose branches and seal each connection with mastic, reinforced with mesh tape where the gap needs it.
Air Handler and Plenum Connections
The connections where supply and return plenums meet the air handler carry the highest pressure in the system. A leak on the return plenum here pulls air from the mechanical room or closet straight into the system. We seal the accessible plenum joints and connections.
Mastic Sealant
Mastic is a thick paste brushed over seams and joints that sets into a flexible, airtight layer. It suits irregular seams, register boot connections, takeoffs and collars, where tape will not sit flat. The National Air Duct Cleaners Association describes mastic as suited to small and medium leaks and durable enough to last for years.
- Irregular seams and joints
- Register boot connections
- Takeoffs and collars
Foil Tape
Foil tape is a metal foil with a heat-resistant adhesive, rated for duct use. It gives a clean seal on flat metal-to-metal joints and reinforces mastic on seams. Ordinary cloth duct tape is not used: it dries out, peels and fails under the heat and pressure inside a duct.
- Flat metal-to-metal joints
- Reinforcing mastic on seams
- Rated for duct use, not cloth tape
Mechanical Fastening
Sealant closes a gap; it does not hold a joint together. Loose sheet metal joints are refastened with sheet metal screws, and flex duct is secured to its collar with a draw band, before any sealant goes on. A joint that is fastened first keeps its seal when the system starts and stops.
Mesh-Reinforced Mastic
Gaps too wide for mastic alone are bridged with mesh tape and covered with mastic, so the seal has something to hold to. If a gap is too large to bridge, or the duct around it is damaged, we recommend repair or replacement of that section instead.
Homes
In homes, the ducts that matter most run through attics, basements, crawl spaces and garages, outside the conditioned space. We seal the joints, seams, takeoffs and boots we can reach there and at every register, and check the runs fully enclosed in finished walls at their accessible ends.
Commercial Buildings
Commercial ductwork above drop ceilings, in mechanical rooms and in exposed installations is sealed on the same principles, scheduled around the building’s hours. Larger trunks and plenum connections usually carry the bulk of the leakage, so they are inspected first.
What Customers Say About Our Duct Repairs
4.7 average from 28 Google reviews across our 8 Google Business listings (listed as JS AirDuct). Every review shown is a real Google review.
Our cracked air duct system was causing us to lose so much heat and AC! After the repairs, our house stays comfortable, and our energy bills have already gone down. That team was very efficient and professional. Thank you!
Our new home needed a complete air duct installation, and this company handled it flawlessly. The technicians were organized, friendly, and respectful of our space. They walked us through each step and made sure everything was sealed tight!
How We Seal Your Ducts
Inspect Accessible Ductwork
We trace the runs in the attic, basement, crawl space or mechanical room and mark failed seams, loose joints, open boots and disconnected branches. Registers are opened to check the boots at every room.
Upfront Price
You see which joints and connections we will seal, and the price, before any work starts. Sections that are too damaged to seal are shown to you and priced as repair or replacement, separately.
Clean First Where Needed
Sealant and tape bond to clean surfaces, and sealing a dirty system locks the dust inside. If the ducts need cleaning as well, we clean them before sealing.
Remove Failed Tape and Dust
Old cloth tape, loose sealant and dust come off each joint, so the new seal sits on bare metal or a clean duct jacket.
Fasten Loose Connections
Loose sheet metal joints are refastened with screws and flex duct is secured to its collar with a draw band. Fastening comes before sealing, so the joint holds its shape when the system cycles.
Seal With Mastic or Foil Tape
Each joint gets the method that suits it: mastic on irregular seams, boots and takeoffs, mesh-reinforced mastic on wider gaps, and foil tape on flat metal joints.
Check Airflow and Walk Through
We run the system, check the registers and walk you through the sealed connections, so you know which parts of the system were sealed and which still need attention.
Why Choose Mint Air Duct Cleaning for Duct Sealing?
Customers choose Mint Air Duct Cleaning for duct sealing because we follow the accepted manual method: inspection before work, duct-rated mastic and foil tape, loose joints fastened before they are sealed, and an upfront price for the joints that need it. Good sealing is careful manual work on every joint, done only on ductwork that is worth sealing, so if a section needs repair or the ducts need cleaning first, our certified, licensed and insured technicians tell you and the same team handles it.
Duct Sealing vs Duct Replacement
Seal your ducts when the duct itself is sound and the leaks are at the seams, joints and register boots; replace the affected sections when the duct material is failing. Sheet metal or flex duct that is still structurally sound, with minor disconnections that can be refastened, is a good candidate for mastic and foil tape. Crushed flex duct, heavy corrosion or moisture-damaged material is different: sealing only delays the problem, and replacement of those sections is the honest recommendation.
Sealing Is Suitable When
The leaks are at seams, joints and connections on ductwork that is still in good shape.
Replacement Is Suitable When
The duct material is failing along the run, not just at the joints.
Types of Air Ducts We Clean, Repair and Install
The main types of air ducts in homes and commercial buildings are rectangular sheet metal, round spiral duct, insulated flex duct, duct board and fiberglass-lined metal duct. Each one collects dust, leaks and wears out differently, so the type of duct decides the cleaning tools, the sealing method and whether a damaged section is repaired or replaced. Our technicians identify the duct type during the inspection and match the work to it.
Rectangular galvanized sheet metal is the standard material for main trunks and for ducts that must fit tight ceilings and walls. Its weak points are the many seams and joints, which we fasten mechanically and seal with mastic or foil tape.
Round galvanized steel duct formed with a continuous lockseam, so a run has fewer joints and less friction than rectangular duct. It needs more clearance, so it suits exposed ceilings, open commercial spaces and long straight runs.
Flexible duct with its own insulation and outer jacket, common for branch runs in attics and crawl spaces. It works well only when pulled straight, strapped so it cannot sag and sealed to its collars; jackets crack with age and rodents chew through it.
Rigid insulated board formed into rectangular duct, so the insulation is the duct wall. It does not tolerate moisture or rough handling: older board crumbles at the edges and its tape lets go, so we tell you when a run should be replaced.
Sheet metal duct with an internal fiberglass liner that quiets airflow. Cleaning must not tear the liner, and according to the EPA no biocides are registered for use on fiberglass-lined duct or duct board, so sanitizing is limited on these runs.
Signs of Leaky Ductwork
Common signs of leaky ductwork include rooms that never reach temperature, higher heating or cooling bills, dust that keeps coming back, whistling at joints or vents, visible gaps or failed tape, stuffy or musty areas and one floor that is always warmer or cooler than the rest. Duct leaks rarely announce themselves directly. They show up as comfort, cost and dust problems first, often in the rooms farthest from the air handler, and they are most likely where ducts run through unconditioned spaces.
Rooms That Never Reach Temperature
Heated or cooled air escapes through leaking seams and joints before it gets to the room at the end of the run, so that room never catches up.
High Heating or Cooling Bills
The system runs longer to make up for air lost into attics, walls or crawl spaces, and the extra runtime shows up on energy bills.
Dust That Keeps Coming Back
Leaks on the return side draw dust from attics, basements and crawl spaces into the system, so surfaces need dusting again soon after cleaning.
Whistling at Joints or Vents
A whistling or hissing sound at joints or vents is air forcing its way through small gaps in the ductwork while the system is under pressure.
Visible Gaps or Failed Tape
Dried, peeling cloth tape at seams and collars, or open gaps you can see at a joint, are direct physical signs that the duct is leaking.
Stuffy or Musty Areas
Stuffy or musty areas can mean air from crawl spaces or basements is entering the system through return leaks and being spread to the rooms.
Uneven Floors
An upper or lower floor that is always warmer or cooler than the rest of the house, even with the system running normally, often points to leaking runs.
Ducts Nobody Has Checked
Attic or crawl space ductwork that has never been inspected is worth checking, because leaks there lose air outside the conditioned space entirely.
Ignoring these signs means paying to heat and cool air that never reaches your rooms, while return leaks keep pulling attic or crawl space dust into the system. If two or more sound familiar, an inspection of the accessible joints is a sensible first step.
What Causes Duct Leaks?
Duct leaks are caused by failed cloth tape, joints that were never sealed, expansion and contraction, building movement and vibration, failed hanging straps, physical damage in attics and crawl spaces, and corrosion from moisture. Most duct leaks come from the connections rather than the middle of a duct section, and most connections fail for one of these reasons. Knowing the cause matters, because a joint that is loose has to be fastened before it is sealed, and a section that is crushed or rusted through may need repair instead of sealant.
Failed Cloth Tape
Cloth duct tape dries out and lets go under the repeated temperature swings inside ducts, which is why it is not used for sealing ductwork.
Joints Never Sealed
Some original installations fastened joints mechanically without sealing them at all, so they have leaked air from the day the system was installed.
Expansion and Contraction
Years of heating and cooling cycles make metal expand and contract, which slowly works seams and joints loose until gaps open along them.
Building Movement and Vibration
Building settling and the vibration of the blower each time it starts gradually pull duct connections apart, especially at long unsupported runs.
Failed Hanging Straps
When hanging straps fail, sagging runs pull flex duct off its collars and put strain on the sheet metal joints they are connected to.
Damage in Attics and Crawl Spaces
Foot traffic, stored boxes and pests in attics and crawl spaces crush or tear ducts, opening holes that let conditioned air escape.
Corrosion From Moisture
Condensation and water leaks eat into sheet metal at seams and joints over time, and corrosion opens gaps that sealant alone may not close.
What Affects Duct Sealing Cost?
The cost of duct sealing depends on the number of joints and register boots, where the ducts run, loose or damaged sections, the size of the system, the duct material, the number of supply and return runs, the sealing method each joint needs and whether the ducts need cleaning first. We price duct sealing after the inspection, by the joints and runs that actually need work, rather than by a flat rate. You see which connections will be sealed and approve the upfront price before we start.
Benefits of Duct Sealing
The benefits of duct sealing are more air reaching the rooms, better comfort in far rooms, shorter system runtime, less dust drawn in from unconditioned spaces, lower backdraft risk, quieter ducts and a clean system that stays clean. ENERGY STAR lists comfort, efficiency, safety and air quality as the benefits of a well-sealed duct system, and it puts typical forced-air losses at 20 to 30 percent of the air moved. Here is what each benefit means in practice.
More Air Reaches the Rooms
Air that was leaking into attics, walls and crawl spaces is delivered through the registers to the rooms it was heated or cooled for.
Better Comfort in Far Rooms
Rooms at the end of long duct runs get their share of heating and cooling once the leaks along the way are sealed with mastic or foil tape.
Less Runtime
A system that is no longer making up for air lost through leaking joints can reach the thermostat setting with shorter heating and cooling cycles.
Less Dust Drawn In
Sealed return ducts stop pulling attic, basement and crawl space dust into the system, so less of it is spread through the house or building.
Lower Backdraft Risk
According to ENERGY STAR, sealed ducts reduce the risk of combustion gases from gas appliances being drawn into living space.
Quieter Ducts
Sealing the small gaps where air forces through under pressure stops the whistling and hissing you could hear at joints, collars and vents.
A Clean System Stays Clean
Sealing after a duct cleaning keeps new dust from entering through the leaks, so the cleaned system stays cleaner for longer between visits.
Ready to Book Duct Sealing? Get an Upfront Price Today
Call (855) 501-0191 or book online and a technician inspects first, explains the duct sealing work your system needs and gives you a clear price before anything starts, 7 days a week.
Our Complete Air Duct Services
Mint Air Duct Cleaning offers every duct and vent service a sealed system depends on, from air duct cleaning before sealing to repair or replacement of sections too damaged to seal, new duct installation and dryer vent cleaning, installation and repair. Duct sealing often sits alongside one of these: dirty ducts are cleaned first so sealant bonds, and crushed or corroded runs are repaired rather than taped over. One team handles the whole job from inspection to walkthrough.
Whole-system cleaning of supply and return ducts, registers, trunk lines and the blower area, using agitation tools and HEPA extraction under negative pressure.
Room-by-room cleaning of every accessible vent in houses, condos, townhouses and apartments, with floors protected and a walkthrough before we leave.
Zone-by-zone cleaning for offices, retail spaces and multi-unit buildings, planned around your business hours so the rest of the building stays in use.
Leaking, disconnected, crushed or deteriorated ducts found, repaired and resealed, or replaced section by section when repair is no longer practical.
New supply and return runs for additions, remodels and reconfigured systems, sized for the rooms they serve, then fastened, sealed and tested.
The full lint line from the back of the dryer to the exterior hood cleared of lint and blockages, followed by an airflow check.
New or rerouted dryer vent lines built from rigid metal duct, with sealed joints and a proper wall or roof termination outside.
Crushed or disconnected vents, loose joints and broken exterior hoods repaired, so hot, moist, lint-laden air leaves the building again.
Duct Systems We Seal
We seal duct systems connected to furnaces and air handlers from every major HVAC manufacturer, because duct sealing works on the ductwork and plenum connections, whoever made the equipment. The seams, joints, takeoffs and register boots that leak are part of the duct system, not the unit, and they are sealed the same way with mastic sealant and foil tape. We seal duct systems connected to equipment from the major manufacturers, including:
Connections We Open and Check
Photos from our own Google Business Profiles.
Schedule Duct Sealing With Mint Air Duct Cleaning
Call (855) 501-0191 or send the booking form with where your ducts run, such as an attic, basement or crawl space, and what you are noticing, from uneven rooms to dust that keeps coming back. We confirm an inspection window, 7 days a week. Your technician marks the leaks, gives an upfront price and seals only the joints you approve, then walks you through the sealed connections.
Air Duct Tips and Guides
What to look for when you hire a residential air duct cleaning company, from equipment and process to clear pricing.
Why clean ducts before guests arrive, and how duct cleaning helps your home feel fresher during the holidays.
Household appliances that can create moisture and mold, and what that means for your air ducts.
Duct Sealing FAQs
What is duct sealant used for?
Duct sealant closes the gaps at seams, joints and connections so air stays inside the ductwork. Mastic is brushed on as a paste and sets into a flexible seal; foil tape covers flat joints. Together they keep conditioned air in and dusty air from unconditioned spaces out.
Is duct sealing worth it?
When ducts leak, yes. ENERGY STAR puts typical forced-air losses at 20 to 30 percent of the air moved, and sealing the reachable joints keeps more of that air in the system and more dust out. It is worth the most when ducts run through attics, crawl spaces or basements outside the conditioned space.
What do HVAC technicians use to seal ductwork?
Mastic sealant and foil tape rated for duct use are the accepted manual materials, with mesh tape under the mastic for wider gaps. Loose joints are fastened with sheet metal screws or draw bands first. That is the method we use.
Can I use regular duct tape on air ducts?
No. Cloth duct tape dries out and lets go under the temperature swings inside ducts. Mastic and foil tape rated for ductwork are the accepted materials.
How long does duct sealing last?
The National Air Duct Cleaners Association describes mastic as durable enough to last for years on small and medium leaks. How long a given joint holds also depends on whether it was fastened and cleaned first, and on whether the duct around it stays undamaged.
Should ducts be cleaned before or after sealing?
Before. Sealant and tape bond to clean surfaces, and sealing a dirty system locks the dust inside. If your ducts need both, we clean first.
Does duct sealing help with dust?
It can, when the dust comes from leaks. Return ducts with gaps in attics, basements or crawl spaces pull dusty air into the system, and sealing those gaps stops that source. Dust already inside the ducts needs cleaning, not sealing.
Can sealing fix rooms that are too hot or cold?
If the room’s supply run is leaking or disconnected, sealing or reconnecting it gets more air to the register. Uneven rooms can also come from undersized runs or equipment problems, which the inspection helps separate from leaks.
Can you seal ducts inside walls and ceilings?
We seal the ductwork we can reach: attics, basements, crawl spaces, mechanical rooms and every register boot. Runs fully enclosed in finished walls are checked at their accessible ends.
Does exposed ductwork need to be sealed?
Exposed ducts in unconditioned spaces such as attics and crawl spaces are where sealing matters most, because every leak there loses air to the outside of the living area.
Do you seal commercial ductwork?
Yes. Ductwork above drop ceilings, in mechanical rooms and in exposed installations is sealed on the same principles, scheduled around the building’s hours.
How long does duct sealing take?
It depends on how many joints and boots need work, which the inspection tells us before you approve the price. See our service areas, or call (855) 501-0191 to check availability.
Stop Losing Air Through Your Ducts
Certified, insured technicians inspect the accessible ductwork, fasten loose joints and seal them with mastic and foil tape, at an upfront price you approve first.
Call (855) 501-0191 or send the form, 7 days a week.