Aeroseal Duct Sealing
Leaks in ducts hidden behind walls, floors and ceilings waste heated and cooled air where no brush can reach. We seal them from the inside with the Aeroseal duct sealing system, measure the leakage before and after, and give you an upfront price first.
- Certified & insured technicians
- Upfront pricing, no add-ons
- Service 7 days a week
- Homes & businesses
Duct Sealing That Reaches the Leaks You Cannot See
Aeroseal duct sealing is an aerosol method that seals leaks from inside existing ductwork, without opening walls, floors or ceilings. The duct system is closed off and pressurized, and a water-based sealant mist is blown into it. As air escapes through cracks and gaps, the sealant particles collect at the edges of each leak and build up until the opening closes.
It is the method for ductwork that manual sealing cannot reach. Mastic and foil tape work on the joints you can get a hand on in an attic or basement, but many ducts run inside finished walls, between floors and above ceilings. According to ENERGY STAR, a typical forced-air system loses 20 to 30 percent of its air through leaks, holes and poorly connected ducts, and much of that loss sits in runs nobody can see.
Our certified, licensed and insured technicians inspect the system first, repair openings too large for the sealant, block the registers and protect the equipment, then run the Aeroseal duct sealing system and show you the leakage readings from before and after the seal. You approve an upfront price before any work begins.
Need Hidden Duct Leaks Sealed Soon?
Rooms that never reach temperature and ducts you cannot get to? Call (855) 501-0191 and we book an Aeroseal inspection, 7 days a week, with an upfront price before sealing.
Aeroseal Duct Sealing Services
Leaks Inside Finished Walls and Ceilings
Ducts that run through finished walls, between floors and above ceilings are sealed without cutting into drywall or plaster. The sealant travels through the duct with the air and closes leaks where they are, so a joint behind a wall gets the same treatment as one in an open basement. This is the main reason homeowners and building owners choose Aeroseal duct sealing over manual sealing: the leaks that cost the most are often the ones nobody can reach.
- No wall or ceiling demolition
- Sealed from inside the duct
- Hidden runs treated like open ones
Seams, Joints and Small Cracks
Seams along duct sections, joints between fittings and small cracks are where most air escapes. According to Aeroseal, the system seals leaks up to 5/8 inch across automatically, without coating the inside of the duct, because the particles only collect where air is escaping. Long trunk lines with dozens of joints are sealed in the same session as the branch runs that feed each room.
- Seams and fitting joints
- Small cracks and pinholes
- Trunk and branch runs together
Takeoffs, Collars and Register Boots
Takeoffs where branches leave the trunk, collars where flex duct connects, and the boots behind each register are common leak points. With the registers blocked during sealing, the gaps around these fittings are closed from the inside along with the rest of the run. Boots that have pulled away from the floor or wall opening are refastened by hand before the system runs.
Openings Too Large for the Sealant
Disconnected ducts, crushed sections and holes wider than the sealant can bridge are found during the inspection and the first pressure reading. According to Aeroseal, larger openings are identified and patched by hand before the sealant is injected. We reconnect, fasten and patch them first, and show you anything that needs repair or replacement as a separate, upfront line before sealing starts.
- Disconnected runs reconnected
- Large holes patched first
- Repairs priced separately
Leakage Measured Before Sealing
The Aeroseal duct sealing system starts with a measurement. The duct system is isolated, a fan pressurizes it, and the software records how much air leaks out at a reference pressure. That baseline reading tells you how leaky the system is before anything is sealed, and it is the number the final reading is compared against.
- Duct system isolated
- Baseline leakage recorded
- Same reference pressure used after
Equipment Protected and Registers Blocked
Before any sealant goes in, the furnace or air handler, the coil and other sensitive components are masked or sealed off from the duct system, and every register is blocked. That keeps the sealant inside the ducts and away from the equipment, the rooms and your furnishings, so the only place it can go is out through the leaks.
Sealant Injected Under Pressure
With the system pressurized, an aerosolized, water-based sealant is injected into the airflow. According to Aeroseal, escaping air carries the particles to each leak, where they deposit at the edges and build up until the opening is sealed. The technician watches a live leakage reading on the computer while the system runs, so the progress of the seal is measured as it happens.
- Water-based sealant mist
- Particles collect only at leaks
- Live leakage reading
Leakage Measured After Sealing
When the sealing run is complete, the system is tested again at the same reference pressure used for the baseline. You see both readings side by side, so the result is a measured number rather than a visual guess. Registers are then unblocked, the equipment is reconnected and the system is run to check airflow.
Homes and Older Houses
In homes, Aeroseal duct sealing suits ducts that run inside finished walls, between floors and through spaces that cannot be reached by hand. Aeroseal says older homes tend to benefit most, because their ductwork often leaks more than owners realize and manual repairs would mean opening walls or ceilings. We work room by room to block registers and protect floors along the work path.
Apartments and Multi-Unit Buildings
Shared duct systems and ventilation runs in multi-unit buildings often pass through walls and shafts that no one can reach without disturbing several units. Sealing from inside the duct avoids most of that access work. We plan the blocking of registers and the equipment shutdown with the building manager before the visit.
Offices and Commercial Buildings
Commercial ductwork above drop ceilings and inside walls is sealed section by section, scheduled around business hours. According to Aeroseal, typical commercial projects reach 80 to 92 percent leakage reduction per sealed section; your own result is the before and after reading we record on your system.
What Customers Say About Our Duct Leak Work
4.7 average from 28 Google reviews across our 8 Google Business listings (listed as JS AirDuct). Every review shown is a real Google review.
Our cracked air duct system was causing us to lose so much heat and AC! After the repairs, our house stays comfortable, and our energy bills have already gone down. That team was very efficient and professional. Thank you!
Our new home needed a complete air duct installation, and this company handled it flawlessly. The technicians were organized, friendly, and respectful of our space. They walked us through each step and made sure everything was sealed tight!
How Our Aeroseal Duct Sealing Service Works
Inspect the Duct System
We trace the accessible runs, open registers and check the air handler connections to understand the layout, the duct type and any obvious damage. This tells us whether Aeroseal duct sealing fits your system or whether manual sealing or repair makes more sense.
Upfront Price
You get a clear price for the sealing, and any repairs that must come first, before work starts. Sections that are too damaged to seal are shown to you and priced separately, so you decide what is done.
Clean First Where Needed
If the ducts are dirty, we recommend cleaning them before sealing, so the sealed system does not keep old dust inside. Duct cleaning is quoted as its own line, and you choose whether to add it.
Protect Equipment and Block Registers
The furnace or air handler, the coil and other sensitive parts are sealed off from the ducts, and every register is blocked, so the sealant stays inside the duct system and away from the rooms.
Measure Baseline Leakage
The Aeroseal duct sealing system pressurizes the isolated ducts and records the leakage before any sealant goes in. If the first reading shows openings too large to seal, we patch them by hand and measure again.
Seal From the Inside
The water-based sealant is injected into the pressurized ducts while the technician watches the live leakage reading drop on the computer. The run continues until the system reaches the end of the sealing process.
Measure Leakage Again
A final test at the same reference pressure records the leakage after sealing. You see both readings side by side, so the improvement on your system is a measured number, not an estimate.
Reconnect and Walk Through
Registers are unblocked, the equipment is reconnected and the system is run to check airflow at the registers. We walk you through the readings, the repairs made and anything that still needs attention.
Why Choose Mint Air Duct Cleaning for Aeroseal Duct Sealing?
Customers choose Mint Air Duct Cleaning for Aeroseal duct sealing because we inspect before we seal, repair large openings by hand first, protect the equipment and rooms, show the leakage readings from before and after, and give an upfront price. Sealing from the inside only pays off on ductwork that is worth sealing, so if a section needs repair, the ducts need cleaning or manual sealing is enough, our certified, licensed and insured technicians tell you.
Aeroseal vs Manual Duct Sealing
Choose Aeroseal duct sealing when the leaks are spread through ducts you cannot reach, and manual sealing with mastic and foil tape when the leaking joints are few and accessible. Manual sealing is hands-on work at each joint in an attic, basement or crawl space. Aeroseal works from inside the duct and reaches runs hidden in walls and ceilings, with leakage measured before and after. Many jobs use both: large openings are fixed by hand, then the system seals the rest.
Aeroseal Is Suitable When
The leaks are many, small and spread through ducts that cannot be reached by hand.
Mastic and Foil Tape Are Suitable When
The leaking joints are few, visible and within reach.
Types of Air Ducts We Clean, Repair and Install
The main types of air ducts in homes and commercial buildings are rectangular sheet metal, round spiral duct, insulated flex duct, duct board and fiberglass-lined metal duct. Each one collects dust, leaks and wears out differently, so the type of duct decides the cleaning tools, the sealing method and whether a damaged section is repaired or replaced. Our technicians identify the duct type during the inspection and match the work to it.
Rectangular galvanized sheet metal is the standard material for main trunks and for ducts that must fit tight ceilings and walls. Its weak points are the many seams and joints, which we fasten mechanically and seal with mastic or foil tape.
Round galvanized steel duct formed with a continuous lockseam, so a run has fewer joints and less friction than rectangular duct. It needs more clearance, so it suits exposed ceilings, open commercial spaces and long straight runs.
Flexible duct with its own insulation and outer jacket, common for branch runs in attics and crawl spaces. It works well only when pulled straight, strapped so it cannot sag and sealed to its collars; jackets crack with age and rodents chew through it.
Rigid insulated board formed into rectangular duct, so the insulation is the duct wall. It does not tolerate moisture or rough handling: older board crumbles at the edges and its tape lets go, so we tell you when a run should be replaced.
Sheet metal duct with an internal fiberglass liner that quiets airflow. Cleaning must not tear the liner, and according to the EPA no biocides are registered for use on fiberglass-lined duct or duct board, so sanitizing is limited on these runs.
Signs Your Ducts Need Aeroseal Duct Sealing
Common signs your ducts need Aeroseal duct sealing include rooms that never reach temperature, high heating or cooling bills, dust that keeps returning, weak airflow at far registers, whistling inside walls, uneven floors, stuffy rooms and ductwork you cannot reach to seal by hand. Hidden duct leaks show up as comfort, cost and dust problems long before anyone sees the leak, and they are most likely in older systems and in ducts that run through walls, floors and ceilings.
Rooms That Never Reach Temperature
Conditioned air escapes through leaks along the run before it reaches the farthest rooms, so those rooms lag behind the thermostat setting every season.
High Heating or Cooling Bills
The system runs longer to make up for air lost inside walls and ceilings, and the extra runtime shows up on the energy bill each month.
Dust That Keeps Coming Back
Return leaks inside wall cavities and attics pull dusty air into the system, so surfaces need dusting again soon after a thorough cleaning.
Weak Airflow at Far Registers
Registers at the end of long runs blow noticeably less air than those near the equipment, a typical sign of leakage along the way.
Whistling Inside Walls
A faint whistle or hiss from inside a wall or ceiling while the system runs is air forcing its way out through gaps in hidden ductwork.
One Floor Always Warmer or Cooler
An upper or lower floor that never matches the rest of the house often points to leaking runs that feed that floor through the walls.
Stuffy or Musty Rooms
Stale or musty air can mean return ducts are drawing air from wall cavities, basements or crawl spaces through leaks you cannot see.
Ducts Nobody Can Reach
When most of the ductwork is enclosed in finished walls and ceilings, manual sealing cannot reach the leaks, and sealing from inside the duct can.
Ignoring these signs means paying to heat and cool air that leaks into wall cavities, ceilings and crawl spaces, while return leaks pull dusty air into the system. If two or more of these sound familiar and your ducts are mostly out of reach, an inspection and a baseline leakage reading are a sensible first step.
What Causes Hidden Duct Leaks?
Hidden duct leaks are caused by joints that were never sealed, failed cloth tape, years of expansion and contraction, building settling and vibration, loose takeoffs and boots, damage during remodeling and corrosion from moisture. Most leaks start at connections rather than in the middle of a duct section, and inside walls and ceilings they go unnoticed for years. Knowing the cause matters, because small gaps suit the Aeroseal duct sealing system while large openings must be repaired by hand first.
Joints Never Sealed
Some original installations fastened duct joints mechanically without sealing them, so those joints have leaked air since the day the system was installed.
Failed Cloth Tape
Cloth duct tape dries out and lets go under repeated temperature swings, leaving gaps at seams and collars that nobody sees inside a wall.
Expansion and Contraction
Years of heating and cooling cycles make metal expand and contract, slowly working seams and joints loose until small gaps open along them.
Building Settling and Vibration
Settling of the structure and the vibration of the blower at every start gradually pull duct connections apart, especially on long hidden runs.
Loose Takeoffs and Boots
Branch takeoffs and register boots that were never fully sealed to the trunk or the building opening leak air into wall and floor cavities.
Damage During Remodeling
Renovation work, new wiring and plumbing can knock, crush or disconnect ducts inside walls and ceilings, and the damage is closed in afterward.
Corrosion From Moisture
Condensation and past water leaks eat into sheet metal at seams and joints, opening gaps that grow over time and may need repair before sealing.
What Affects Aeroseal Duct Sealing Cost?
The cost of Aeroseal duct sealing depends on the size of the duct system, the number of HVAC systems, how leaky the ducts are, the number of registers to block, repairs needed before sealing, whether the ducts need cleaning first, access to the equipment and the type of property. We price after the inspection, based on your actual system rather than a flat rate, and you approve the upfront price before we start.
Benefits of Aeroseal Duct Sealing
The benefits of Aeroseal duct sealing are more conditioned air reaching the rooms, sealed leaks in ducts nobody can reach, no wall or ceiling demolition, measured results, better comfort in far rooms, less dust drawn in through return leaks and shorter system runtime. ENERGY STAR puts typical forced-air losses at 20 to 30 percent of the air moved, and sealing from the inside reaches leaks that manual methods leave behind. Here is what each benefit means in practice.
Reaches Hidden Ductwork
Ducts inside finished walls, between floors and above ceilings are sealed from the inside, so the leaks that cost the most are no longer out of reach.
No Demolition
The sealant travels through the ducts with the air, so walls, floors and ceilings stay closed and there is no drywall or plaster to repair afterward.
Measured Results
Leakage is recorded before and after sealing at the same pressure, so you see a measured improvement on your own system rather than a promise.
More Air Reaches the Rooms
Air that was leaking into wall cavities and ceilings is delivered through the registers to the rooms it was heated or cooled for.
Better Comfort in Far Rooms
Rooms at the end of long runs get their share of air once the leaks along the way are sealed, which evens out temperatures between rooms.
Less Dust Drawn In
Sealed return ducts stop pulling dusty air from wall cavities, attics and crawl spaces into the system, so less dust is spread through the rooms.
Shorter Runtime
A system that no longer makes up for lost air can reach the thermostat setting with shorter heating and cooling cycles.
Water-Based Sealant
According to Aeroseal, the sealant is water-based, non-toxic and low in VOCs, and it is certified to UL 1381 and UL 723 for use in ductwork.
Ready to Book Aeroseal Duct Sealing? Get an Upfront Price Today
Call (855) 501-0191 or book online and a technician inspects first, explains the aeroseal duct sealing work your system needs and gives you a clear price before anything starts, 7 days a week.
Our Complete Air Duct Services
Mint Air Duct Cleaning offers every duct and vent service a sealed system depends on, from air duct cleaning before sealing and manual duct sealing with mastic to repair of sections too damaged to seal, new duct installation, air duct sanitizing and dryer vent work. Aeroseal duct sealing often sits alongside one of these: dirty ducts are cleaned first, large openings are repaired by hand, and accessible joints can be sealed manually. One team handles the whole job from inspection to walkthrough.
Whole-system cleaning of supply and return ducts, registers, trunk lines and the blower area, using agitation tools and HEPA extraction under negative pressure.
Room-by-room cleaning of every accessible vent in houses, condos, townhouses and apartments, with floors protected and a walkthrough before we leave.
Zone-by-zone cleaning for offices, retail spaces and multi-unit buildings, planned around your business hours so the rest of the building stays in use.
Leaking, disconnected, crushed or deteriorated ducts found, repaired and resealed, or replaced section by section when repair is no longer practical.
New supply and return runs for additions, remodels and reconfigured systems, sized for the rooms they serve, then fastened, sealed and tested.
Leaking seams, joints and register boots mechanically fastened, then sealed with mastic and foil tape so conditioned air reaches the rooms.
The full lint line from the back of the dryer to the exterior hood cleared of lint and blockages, followed by an airflow check.
New or rerouted dryer vent lines built from rigid metal duct, with sealed joints and a proper wall or roof termination outside.
Crushed or disconnected vents, loose joints and broken exterior hoods repaired, so hot, moist, lint-laden air leaves the building again.
An EPA-registered antimicrobial product applied after a full cleaning, only where the label allows it and only when the condition of the ducts calls for it.
Duct Systems We Seal With Aeroseal
We seal duct systems connected to furnaces and air handlers from every major HVAC manufacturer, because Aeroseal duct sealing works on the ductwork, not the equipment. The equipment is sealed off from the ducts before the sealant goes in and reconnected afterward, so the brand of the unit does not change how the leaks are sealed. We seal duct systems connected to equipment from the major manufacturers, including:
Connections We Check Before Sealing
Photos from our own Google Business Profiles showing the registers, boots and equipment we open and check before any sealing.
Schedule Aeroseal Duct Sealing With Mint Air Duct Cleaning
Call (855) 501-0191 or send the booking form with where your ducts run and what you are noticing, from rooms that never reach temperature to dust that keeps coming back. We confirm an inspection window, 7 days a week. Your technician checks the system, gives an upfront price, measures the leakage, seals from the inside and shows you both readings.
Air Duct Tips and Guides
What to look for when you hire a residential air duct cleaning company, from equipment and process to clear pricing.
Why clean ducts before guests arrive, and how duct cleaning helps your home feel fresher during the holidays.
Household appliances that can create moisture and mold, and what that means for your air ducts.
Aeroseal Duct Sealing FAQs
What is Aeroseal duct sealing?
Aeroseal duct sealing is an aerosol method that seals leaks from inside existing ductwork. The duct system is closed off and pressurized, and a water-based sealant mist is blown in. As air escapes through gaps, the particles collect at the edges of each leak and build up until it closes, without opening walls, floors or ceilings.
Is Aeroseal worth it?
It is worth the most when your ducts leak and most of them run inside walls, floors or ceilings where manual sealing cannot reach. ENERGY STAR puts typical forced-air losses at 20 to 30 percent of the air moved. If the leaking joints are few and exposed, manual sealing with mastic and foil tape may be enough, and we will tell you.
Is Aeroseal duct sealing safe?
According to Aeroseal, the sealant is water-based, non-toxic, non-flammable and low in VOCs, and it is certified to UL 1381 and UL 723. During sealing, the registers are blocked and the equipment is sealed off, so the sealant stays inside the duct system.
Are there any health risks associated with Aeroseal?
Aeroseal describes its sealant as water-based and low in VOCs, with no strong odor. If anyone in your home has chemical sensitivities, tell us when you book, and we will go through the process and the sealant information with you before the visit.
What do you use to seal ducts?
Two methods: manual sealing with duct-rated mastic and foil tape on joints we can reach, and the Aeroseal duct sealing system for leaks inside ducts that cannot be reached by hand. Loose joints and large openings are fastened and patched by hand first in both cases.
How big a leak can Aeroseal seal?
According to Aeroseal, the system seals leaks up to 5/8 inch across automatically. Larger openings, disconnected runs and crushed sections are found during the inspection and first reading, and are repaired by hand before sealing.
Does Aeroseal coat the inside of the ducts?
According to Aeroseal, no. The sealant particles stay suspended in the air and only collect where air is escaping, at the edges of leaks, rather than coating the duct walls.
How long does Aeroseal duct sealing take?
Aeroseal says most jobs are done in a day. The time on your system depends on its size, how leaky it is, the number of registers to block and any repairs needed first, which the inspection tells us before you approve the price.
Do I need to leave the house during sealing?
Plan for the technician to work through the rooms to block registers and at the equipment to seal it off. We tell you before the visit which rooms we need, how long the system will be off and whether anyone with sensitivities should step out while the sealant runs.
Should ducts be cleaned before Aeroseal?
If they are dirty, yes. Cleaning first removes the dust and debris that would otherwise stay inside a newly sealed system. We quote cleaning as a separate line and you decide whether to add it.
How is Aeroseal different from manual duct sealing?
Manual sealing is done by hand at each reachable joint with mastic and foil tape. Aeroseal seals from the inside, reaches ducts hidden in walls and ceilings, and measures the leakage before and after. Many systems need both.
Do you use Aeroseal on commercial buildings?
Yes. Commercial ductwork is sealed section by section and scheduled around business hours, with readings recorded for each section. See our service areas, or call (855) 501-0191 to check availability.
Seal the Duct Leaks You Cannot Reach
Certified, insured technicians inspect your system, repair large openings, seal hidden leaks from the inside with the Aeroseal duct sealing system and show you the readings, at an upfront price you approve first.
Call (855) 501-0191 or send the form, 7 days a week.